 PRODUCT
CODE: TE/TE 041
Single conductors are carefully selected and matched to meet
or exceed ANSI MC 96.1-1982 tolerances.
Each conductor
is insulated with 8 mils nominal of -400°F to +400°F (-240°C
to +204°C) flame resistant and low smoke FEP to insure insulation
integrity.
Matched pairs
are twisted to reduce the amount of electromagnetic interference.
The
twisted pairs are cabled and a polyester backed aluminum shield with
a tinned copper drain is helically applied overall to further reduce
electrostatic noise. The shield overlaps approximately 25% to assure
continual coverage during flexing.
This
construction includes an insulated communication wire to transmit telephone
or other signals during installation or service.
A
rugged -400°F to +400°F(-240°C to +204°C) flame resistant
and low smoke FEP Teflon jacket is applied over the pairs for excellent
resistance to most corrosive substances, lubricants and weathering.
This construction simplifies installation in cable trays and conduit
due to its proprieties of low friction, good flexibility and mechanical
strength.
When
multi-pair constructions are purchased, the individual pairs are numbered
for easy hookup.
The
entire construction is color coded according to ANSI MC 96.1-1982 to
aid in quick identification of both polarity and calibration.
A
nylon ripcord is included for easy jacket stripping.
|
| No.
of Pairs |
Part
Numbers |
| Type
J |
Type
K |
Type
T |
Type
E |
Type
N |
Type
R/S |
| 1 |
JX-201TE/TE031-20U |
KX-201TE/TE31-20U |
TX-201TE/TE31-20U |
EX-201TE/TE31-20U |
NX-201TE/TE31-20U |
RSX-201TE/TE31-20U |
| 4 |
JX-204TE/TE041-20U |
KX-204TE/TE041-20U |
TX-204TE/TE041-20U |
EX-204TE/TE041-20U |
NX-204TE/TE041-20U |
RSX-204TE/TE041-20U |
| 6 |
JX-206TE/TE041-20U |
KX-206TE/TE041-20U |
TX-206TE/TE041-20U |
EX-206TE/TE041-20U |
NX-206TE/TE041-20U |
RSX-206TE/TE041-20U |
| 8 |
JX-208TE/TE041-20U |
KX-208TE/TE041-20U |
TX-208TE/TE041-20U |
EX-208TE/TE041-20U |
NX-208TE/TE041-20U |
RSX-208TE/TE041-20U |
| 12 |
JX-212TE/TE041-20U |
KX-212TE/TE041-20U |
TX-212TE/TE041-20U |
EX-212TE/TE041-20U |
NX-212TE/TE041-20U |
RSX-212TE/TE041-20U |
| 16 |
JX-216TE/TE041-20U |
KX-216TE/TE041-20U |
TX-216TE/TE041-20U |
EX-216TE/TE041-20U |
NX-216TE/TE041-20U |
RSX-216TE/TE041-20U |
| 20 |
JX-220TE/TE041-20U |
KX-220TE/TE041-20U |
TX-220TE/TE041-20U |
EX-220TE/TE041-20U |
NX-220TE/TE041-20U |
RSX-220TE/TE041-20U |
| 24 |
JX-224TE/TE041-20U |
KX-224TE/TE041-20U |
TX-224TE/TE041-20U |
EX-224TE/TE041-20U |
NX-224TE/TE041-20U |
RSX-224TE/TE041-20U |
| 36 |
JX-236TE/TE041-20U |
KX-236TE/TE041-20U |
TX-236TE/TE041-20U |
EX-236TE/TE041-20U |
NX-236TE/TE041-20U |
RSX-236TE/TE041-20U |
| 50 |
JX-250TE/TE041-20U |
KX-250TE/TE041-20U |
TX-250TE/TE041-20U |
EX-250TE/TE041-20U |
NX-250TE/TE041-20U |
RSX-250TE/TE041-20U |
|
| NOTE: |
The
part numbers above represent the more popular constructions. However,
other designs are available upon request. |
Color
Code & Initial Calibration Tolerances for Extension Wire:
| Thermocouple
Type |
Color
Code |
Initial
Calibration Tolerances |
| Wire
Alloys |
ANSI
Symbol |
+/-
Individual |
Jacket |
Temperature
Range |
Standard
Limits |
Special
Limits |
| *Iron
vs. Constantan |
JX |
White/Red |
Black |
+32°F
(0°C) to +400°F (+200°C) |
±
4°F (2.2°C) |
±
2°F (1.1°C) |
| CHROMEL® vs. ALUMEL® |
KX |
Yellow/Red |
Yellow |
+32°F
(0°C) to +400°F (+200°C) |
±
4°F (2.2°C) |
±
2°F (1.1°C) |
| Copper
vs. Constantan |
TX |
Blue/Red |
Blue |
-75°F
(-60°C) to +210°F (+100°C) |
±
2°F (1.1°C) |
±
1°F (.5°C) |
| CHROMEL® vs. Constantan |
EX |
Purple/Red |
Purple |
+32°F
(0°C) to +400°F (+200°C) |
±
3°F (1.7°C) |
±
2°F (1.1°C) |
| Nicrosil vs. Nisil |
NX |
Orange/Red |
Orange |
+32°F
(0°C) to +400°F (+200°C) |
±
4°F (2.2°C) |
±
2°F (1.1°C) |
| Copper
vs. Copper Alloy |
SX
/ RX |
Black/Red |
Green |
+75°F
(+25°C) to +400°F (+200°C) |
±
9°F (5°C) |
|
|
| NOTE: |
Percent
limits apply directly to temperature in °C units, but for °F equivalents
are applied to the numbers of °F above or below the ice point (+32°F).
(i.e. Limit (°F) = (Temp. °F-32°F) x Percentage) |
|
Thermocouple
wire cannot be expected to meet the limits of error at temperatures
below the ice point unless specified at time of purchase. |
| * |
Magnetic |
|
CHROMELŪ
and ALUMELŪ are registered trademarks of Hoskins Manufacturing Company. |
| TE/TE
041 Physical Properties: |
No.
of Parts |
Nominal
Jacket
Thickness (mls) |
Nominal
O.D.
(in.) |
Min.
Bend
Radius
(in.) |
Maximum
Pulling
Tension
(lbs) |
Average
of
TC Types Net
WT/1000
Ft. (lbs.) |
| Characteristics |
Insulation |
Jacket |
|
Operating Temperature (max.) |
400°F
(204°C) |
400°F
(204°C) |
| 1 |
| 4 |
| 6 |
| 8 |
| 12 |
| 16 |
| 20 |
| 24 |
| 36 |
| 50 |
|
| 15 |
| 15 |
| 15 |
| 15 |
| 20 |
| 20 |
| 20 |
| 20 |
| 20 |
| 20 |
|
| .131 |
| .237 |
| .275 |
| .304 |
| .371 |
| .419 |
| .439 |
| .501 |
| .573 |
| .663 |
|
| 1.000 |
| 1.700 |
| 1.900 |
| 2.100 |
| 2.500 |
| 2.900 |
| 3.000 |
| 3.500 |
| 4.000 |
| 4.800 |
|
| 20 |
| 74 |
| 106 |
| 139 |
| 204 |
| 270 |
| 335 |
| 401 |
| 597 |
| 826 |
|
| 16 |
| 49 |
| 67 |
| 85 |
| 126 |
| 162 |
| 196 |
| 232 |
| 335 |
| 462 |
|
| Melting
Point |
530°F
(277C) |
530°F
(277°C) |
| Tensile
Strength; psi (min) |
2500 |
2500 |
| Elongation;
%(min) |
250 |
250 |
Cold
Bend
(Operating Temperature) |
-4°F
(-2°C) |
-4°F
(-2°C) |
| Specific
Gravity |
2.15 |
2.15 |
| Water
Absorgtion |
0.1% |
0.1% |
Heat
Aged 7 Days at Indicated Temp.
-Redication of Tensile Strength
-Retention of Elongation |
|
|
| Flammability |
Self
Extinguishing |
Self
Extinguishing |
|
|
| Pricing
Policy: |
Shipments
will be invoiced at PMC's prices in effect at time of shipment. Quotations
are given with an escalation clause and prices, terms, and conditions
are subject to change without prior notice. PMC will however, make every
attempt to hold to current quoted prices. All prices are in United States
currency, and shall be subject to correction for errors, unless otherwise
stated in writing to PMC.
|
| Reels,
Spools & Coils: |
All shipments,
unless specified otherwise by PMC, are make on non-returnable reels, spools
or coils in one continuous length. |
Shortages & Returns: |
All claims
for shortage or incorrect material must be made within 10 days after receipt
of the goods to which such claim pertains. Goods may only be returned
for credit within 1 month of the date of authorization. Goods that are
special in any way shall not be returned to PMC. Material returned for
any reason, without written authorization will be refused a n returned
at shipper's expense. A return request must be processed through our Manchester,
N.H. sales office. |
| Tolerances: |
Due to
allowances in manufacturing processes for wire, cable and similar products,
PMC-A Division of R-SCC reserves the right to ship variation of ±
10% from the quantity of such goods ordered. Physical tolerances shown
are nominal. Shipping weights are an average of all types of conductors
and are listed for estimation only. These weights can vary substantially
due to different types of spools, reels and/or conductors.
The material
contained in the document is presented in good faith and believed to
be reliable and accurate. However, because testing conditions may vary
and material quality or information that may be provided in whole or
part by others may be beyond our control, no warranty, expressed or
implied, is given PMC-A Division of R-SCC can assume no liability for
results obtained or damages incurred through the application of the
data tests presented.
Note: PMC-A Division of R-SCC reserves the right to substitute an equal
product on all registered trademark items.
|
Build
your own Part Number |
